The mining system applied by PT Bukit Baiduri Energi is an open pit mining system utilizing the open-pit method. The application of the open-pit method creates a depression that has a high potential to become a catchment area for both surface runoff and groundwater. In the mining pit of PT Bukit Baiduri Energi, there is a sump located at an elevation of -86 meters above sea level (mdpl). The planned mining boundary is at an elevation of -110 mdpl. Therefore, this research aims to determine the area of the catchment, runoff discharge values, sump capacity, and pump capacity, so that the volume of incoming water can be known, allowing for the control of the sump to prevent overflow that could disrupt mining activities.. Based on the data obtained and the calculations performed, the catchment area was found to be 103.42 ha. In the calculation of runoff discharge using the rational method, the total runoff discharge entering sump A9 was found to be 4,211.66 m3/day. The capacity of the sump was measured at 125,187.62 m3. In the pump capacity calculation, the pump capacity based on the pumping discharge was found to be 2,926.80 m3/day.

Disposal area is an area at an open pit mine that is used as a place to store or dispose of worthless materials. Disposal must also follow the specified safety factor standards, if the disposal design is not safe after being analyzed by a geotechnical engineer, the design must be redesigned to achieve the desired safety factor value. One way to increase the fk value is to make a Counterweight plan in making disposal. Where Counterweight is a fill material that is made with special treatment so that the soil bearing capacity increases which functions to withstand the load on it. Landslides on disposal slopes are one of the serious problems faced in mining activities, especially in areas with vulnerable geological and topographic conditions. PT Jembayan Muarabara, which operates in Marangkayu District, Kutai Kartanegara Regency, East Kalimantan Province, is no exception to this challenge. The A–A’ cross section shows a safety factor value of 1.118 in saturated conditions, which indicates that the slope is at a stable limit and needs to be improved through engineering such as adding counterweights. The B–B’ cross-section has a safety factor value of 2.332, which is included in the safe category and has met the provisions of the ESDM Ministerial Decree No. 1827 K/30/MEM/2018. The C-C’ cross-section has a safety factor value of 1.511, which is included in the safe category and has met the provisions of the ESDM Ministerial Decree No. 1827 K/30/MEM/2018.

In the Kutai Basin area, seasonal changes such as high rainfall can significantly increase groundwater content, so that the effect of water content on the shear strength of claystone, increasing water content in rocks tends to decrease shear strength. Water in the pores or fractures can increase pore water pressure and reduce effective normal stress. Shear strength is one of the most important mechanical parameters used to assess soil and rock stability, this parameter is very important in slope stability analysis, foundation planning, and various civil engineering and mining applications. Therefore, this study was conducted to determine whether the water content in rocks can affect the strength of rocks in receiving shear forces. The method used in this study is more quantitative and specific to the effect of water content on the shear strength of claystone in this area. Increasing water content in rocks tends to reduce shear strength. This study was conducted by taking claystone samples from several locations in the Kutai Basin. Data collection in the form of primary data and secondary data for testing physical properties and testing mechanical properties, in testing physical properties, the water content value will be taken as supporting data which is one of the factors that affect rock strength, in testing mechanical properties, claystone shear strength data will be taken. From the results of the physical properties test calculations, the air content in each Formation is obtained, namely, in the Kampungbaru Formation the minimum air content value is 15.54% and the maximum is 20.17%, in the Balikpapan Formation the minimum air content value is 10.21% and the maximum is 12,88%, in the Palaubalang Formation the minimum air content value is 10.49% and the maximum is 22.87%. The results of the strength of the claystone in receiving shear forces in the Kutai Basin are the Muara Jawa location 0.486MPa, Tanah Datar location 0.500 MPa, Sanga-sanga location 0.333 MPa, Muara Badak location 0.269, Air Putih location 0.711MPa, Mugirejo location 0.021 MPa and Lempake location 0.092 MPa.

Durability is defined as a measure of a rock's resistance to weathering and disintegration when the rock undergoes weathering processes over a short period of time. The susceptibility of rocks to disintegration is related to their low durability. Rock durability is often measured using the slake durability test. The slake durability test is widely used to assess physical changes resulting from wetting-drying processes (Franklin and Chandra, 1972). Therefore, slake durability testing is conducted to understand the weathering of rocks caused by heat and water, particularly clay stones which are one of the constituent rocks on a slope. The sampling location is around Sanga-sanga and Muara Badak. Sampling was conducted with coordinate points and the Balikpapan and Kampungbaru formations. The claystone samples taken were then brought to the Mineral and Coal Technology Laboratory of the Engineering Faculty of Mulawarman University for Slake Durability tests. In this study, the lowest index value obtained was 45.7% and the highest value was 93%, indicating high to very high durability. The difference in the durability index values of claystone at the research locations indicates the presence of variables that can affect the slake durability index values of the claystone in the Balikpapan and Kampungbaru formations, including grain size and mineral content as well as geological conditions at the research site. Based on the results of the claystone durability tests, the durability index value (Id2) was obtained, indicating that the sandstone at the research location falls into the classification of high to low.

Compressive strength is one of the mechanical properties of rock behavior. This study focuses on the Balikpapan and Kampungbaru Formations located in the Kutai Kartanegara area, East Kalimantan. The Schmidt Hammer testing method was applied due to the lack of previous studies utilizing this tool to evaluate rock hardness in correlation with compressive strength. The research site is situated in the Kutai Kartanegara area, specifically in the districts of Muara Badak, Muara Jawa, and Sanga-Sanga. Field observations revealed the presence of claystone slopes at predetermined locations. Based on the test results, the uniaxial compressive strength (UCS) values for the Balikpapan Formation range from 3.453 MPa to 5.454 MPa, while the Kampungbaru Formation ranges from 3.317 MPa to 8.571 MPa. The Schmidt Hammer rebound number (RN) values for the Balikpapan Formation range from 17 to 19.6, and for the Kampungbaru Formation from 15 to 23.7. A negative correlation was found between the rebound number and UCS, where higher RN values tend to correspond with lower UCS values. This is supported by the linear regression analysis showing a negative coefficient (-0.450).
 

This study discusses the use of the Quick Response Code Indonesian Standard (QRIS) as a cashless digital payment tool from the perspective of Islamic commercial jurisprudence (fiqh muamalah). QRIS is an electronic payment system recognized by Bank Indonesia to facilitate non-cash transactions in the country. From an Islamic legal standpoint, it is essential to analyze the validity of transactions and the underlying akad (contracts), as sharia principles require clarity (bayyinah), mutual consent (ridha), and the lack of riba (usury), gharar (uncertainty), and maisir (gambling). This research adopts a descriptive quantitative approach and literature study method to examine QRIS in the context of fiqh muamalah, particularly focusing on the validity and contracts involved in non-cash payments. The findings of this study indicate that the use of QRIS in financial transactions can be considered valid under Islamic law, provided it fulfills the essential elements and conditions of a valid contract, such as price clarity, transaction object, and mutual consent.Keywords : QRIS, Fiqh Muamalah, Non-Cash Transaction, Akad Islamic Economics

This study discusses the concept and online buying and selling transactions that comply with sharia principles. This study aims to analyze the validity of online buying and selling transactions based on the perspective of fiqh muamalah. This study uses qualitative descriptive and literature research methods by examining materials related to the Analysis of Online Shopping Transactions in the Perspective of Fiqh Muamalah and Sharia compliance. The results of the study indicate that online shopping transactions can be considered valid according to sharia if they meet four main requirements, namely the existence of the transacting parties, the existence of ijab and qabul, clarity of the object of the transaction, and a halal purpose. In addition, the principles of transparency, honesty, and freedom from usury and gharar are important requirements in maintaining the justice and validity of online buying and selling according to Islamic law.Keywords : Online buying and selling, Islamic jurisprudence, Sharia compliance, Transaction validity, Offer and acceptance

This study aims to investigate the role of SWOT analysis in the strategic decision-making process at Warcaf, Warcaf is a business operating in the culinary sector. In the context of increasingly tight business competition today, it is very important for a company to have a good strategy in order to remain competitive in the market. SWOT analysis, including the recognition of strengths, weaknesses, opportunities, and threats, serves as a fairly efficient instrument in designing strategies that are in accordance with the company's internal and external situations. The method applied in this study is a qualitative approach, where information is obtained through in-depth interviews with Warcaf management. This study shows that SWOT analysis not only plays a role in the strategic decision-making process, but also as a basis for long-term planning. It is expected that this study can provide contributions such as information and strategies in the culinary industry.

Mathematics is one of the subjects taught at all levels from basic education to higher education, which has a significant role in preparing students to have the ability to think logically, analytically, systematically, critically and creatively, as well as have the ability to work together. One of the activities in learning mathematics at school is through problem solving. Problem solving aims to see students' understanding of a material. Mathematical problem solving ability is a very important part of learning mathematics. However, in reality, the problem-solving ability of junior high school students' mathematics is still very low. From these problems, then one of the lessons that can improve the ability to solve mathematical problems is Problem Solving learning. One of the factors that influence differences in problem solving ability is learning style. Learning styles have a close relationship and influence on the learning process in order to achieve learning goals. With students knowing their learning style, learning Problem Solving can be done easily. The subjects of this study were students of class VIII A MTs Plus Sunan Drajat Kedungsantren Bojonegoro. The purpose of this study was to determine the effectiveness of Problem Solving learning on mathematics learning outcomes when viewed from students' learning styles. The type of research used is quantitative research with the One Group Pretest-Posttest Design. The results showed that testing the data on mathematics learning outcomes with the Paired Sample T-Test stated that the t_count value was -9.726. The t_count value is negative, because the pretest average value is lower than the posttest average value. In this case, the t_count value can be positive so that it becomes 9.726. Meanwhile, the value of t_table with ? = 0.05 and degrees of freedom (dk=n-1) with 24 students is 1.714. Then it can be seen that t_count > t_table, then H0 is rejected and Ha is accepted, meaning that there is a significant difference. So it can be concluded that the application of the Problem Solving learning model is quite effectively carried out in the teaching and learning process for class VIII A students of MTs Plus Sunan Drajat Kedungsantren on the material of geometric shapes on the flat sides of cubes and blocks.
 

This article explores the significance of gaining a clear understanding of the topic concept addition as the main foundation in mathematical literacy. This study examines various pedagogical approaches in introducing the concept of addition to students, emphasizing the importance of conceptual understanding compared to procedural learning. Analysis of several learning methods shows that the use of manipulative objects, visual representations, and the application of real contexts significantly improve students' understanding of the idea behind addition. The results of the research also indicate that difficulties in understanding the concept of addition at the early stage of Learning may affect the progress of advanced mathematical abilities. This article concludes that a learning approach that emphasizes conceptual understanding of addition as a quantity combination operation will establish a strong basis for the advancement of students' mathematical abilities in the future.