Management and characteristics of B3 waste at PT Ketenagalistrikan based on the potential hazards produced have been carried out by grouping and storing B3 waste based on physical, chemical and based on potential hazards with the aim of security and safety in the Temporary Storage Warehouse for B3 Waste. PT. Ketenagalistrikan has implemented a comprehensive Hazardous and Toxic Materials (B3) waste management system based on Government Regulation No. 22 of 2021 and Regulation of the Minister of Environment and Forestry No. 6 of 2021. Power plant operational activities produce various types of B3 waste such as used oil, used batteries, and other contaminated materials. B3 waste management is carried out through the stages of identification, sorting, containerization, labeling, temporary storage at licensed B3 TPS, as well as transportation and processing by licensed third parties. A quarterly recording and reporting system to environmental agencies is also carried out routinely. This program has succeeded in reducing the risk of environmental pollution and increasing the company's compliance with applicable B3 waste management regulations. Occupational Safety and Health (K3) at PT. Electricity, especially in the handling and storage of Hazardous and Toxic Materials (B3) waste, also plays an important role in avoiding unwanted things. B3 waste generated from PT. Ketenagalistrikan office operations such as used lubricants, batteries, used TL lamps, printer cartridges, and other electronic equipment require special handling in accordance with Government Regulation No. 22 of 2021. Compliance with K3 standards in the storage of B3 waste is an effort to minimize the risk of environmental pollution and potential health problems for workers. The implementation of K3 in the storage of B3 waste in PT. Ketenagalistrikan offices not only fulfills regulatory obligations but also supports the company's commitment to environmental sustainability in accordance with ISO 14001:2015, as well as ensuring the safety and health of its workers.

PT X, one of the state-owned enterprises to support the country's food security, is the largest and most comprehensive fertilizer producer in Indonesia that generates various wastes, including industrial liquid waste. Liquid waste has no economic value, so it is very important to treat it. PT X Company uses potential Hydrogen (pH)ysical and chemical treatment. There are two effluent treatment units, setting, line injection, and sludge treatment. All parameters evaluated include chemical requirements for oxygen (COD), zat padat yang tersuspensi(TSS), ammonia (NH3), total kjehdal nitrogen (TKN), fluorine, degree of acidity (potential of hydrogen (pH)), oil, and fat. According to the results after the analysis conducted in the study, it was found that the air pollution data after wastewater treatment was carried out showed that the quality of wastewater every month had met the quality standards of the rules and could be discharged into water bodies / seas. This shows the effectiveness of the treatment process implemented by the company.

The fabric printing industry makes a major contribution to various kinds of textile products, its by-products, liquid waste, require special attention in environmental management.
Most of the liquid waste originating from the fabric printing industry consists of dyes, solvents and other processing chemicals. To prevent negative effects on water quality and the surrounding environment, managing this waste is very important. To achieve sustainability, advances in liquid waste processing technology are very important. The solution to reduce the impact of liquid waste from the fabric printing industry is an advanced purification process. PT. X to reduce polutan parameter such BOD, COD , TSS, Ammonia and Total Colidform by. 90%, 95%, 95%, 85%, 20%, 90% And meets the specified quality standards. Because the pH parameters still meet existing quality standards, processing is focused on reducing the organic parameters which are quite high. The results of the process will be used again for flushing activities in green open spaces and for washing operational vehicles.

In the wastewater industry, it is divided into 2, specifically wastewater from home activities and production. Domestic activity wastewater comes from all worker sanitation activities and industrial supporting facilities such as prayer rooms, canteens and toilets. Waste water from these activities must be treated first so that it does not pollute the surrounding environment. PT X is an industry that operates in the field of bulk LPG filling stations which has made efforts to process and also utilize 100% of the waste water from its domestic activities. Sewage Treatment Plants handle the processing (STP) facilities with chemical and biological processes which are able to reduce pollutant parameters such as BOD, COD, TSS, Ammonia and Total Coliform by 90%, 85%, 95%, 90% and 99.9% and have been meet the specified quality standards. Meanwhile, oil & fat parameters are not too focused because they still meet existing quality standards, Therefore, processing aims to lower the relatively high organic characteristics. The results of this processing will be reused to reduce the use of clean water for irrigating green open spaces and roads.