Publication Search

Naturally, a mother hen incubates her eggs until they hatch completely. However, the success rate of natural hatching is low, and hatching can be completed with a maximum of 10 eggs. Chicken farming, more specifically the chicken egg hatching system, breeders usually use an incubator for the process of hatching chicken eggs. In the incubator, there is a lamp that has been provided which is used for the process of warming the eggs so that the eggs can hatch properly and of good quality with incandescent lamps. In general, the process of hatching eggs often encounters problems or obstacles. The obstacle that is often experienced when hatching chicken eggs is that the incubator only uses incandescent lights. Therefore, to avoid this problem, a microcontroller was designed to overcome this problem. This tool is a combination of a microcontroller with an Arduino-based temperature and humidity sensor. With this tool, after the eggs hatch, when the lights are off, the sensor can read the output in the form of the incubator temperature, which is detected by the Arduino serial display. Design methods and experimental methods were used in this research. Tool testing is divided into three types, namely temperature testing, humidity testing and egg load testing. The result of this research is an automatic egg incubator machine that uses Arduino. Several electronic components used in the incubator are Arduino,

Peningkatan tingkat kriminalitas dan keahlian para pencuri yang semakin tinggi, membuat penulis memperoleh ide atau gagasan inovasi alat pengaman pintu rumah menggunakan Radio Frequency Identification (RFID) berbasis arduino uno yang tentunya dengan sistem pengamanan yang tinggi. Rancangan keamanan ini tidak mengandalkan mekanik sebagai  interface nya melainkan menggunakan  perangkat elektronik yang cukup sulit  untuk dibobol karena selain diperlukan  pengetahuan mengenai elektronik, para  pelaku kriminalitas juga harus memilki  pengetahuan dibidang pemrograman dan  teknologi informasi. Berbeda dengan kunci  mekanik, kunci elektronik pada rancangan  keamanan ini menggunakan  Radio  Frequency Identification (RFID) sebagai  pembukanya. RFID (Radio Frequency Identification) merupakan proses pengidentifikasian suatu objek secara otomastis dengan frekuensi radio. Ada dua komponen penting dalam sistem RFID yaitu kartu (Tag) dan pembaca (reader). Dalam perancangan alat ini, RFID digunakan untuk menghidupkan sistem engine cut off yang ada pada sepeda motor untuk pemutus arus pada CDI sepeda motor, tanpa harus melepas kepala aki yang kadang membutuhkan waktu yg cukup lama. Dalam sistem ini pemilik kendaraan bertindak sebagai RFID tag berisi serial khusus yang menginformasikan tentang kepemilikan yang terdapat pada gantungan kunci pemilik kendaraan dan sepeda motor sebagai RFID reader yang berfungsi sebagai pembaca dari informasi yang ada pada gantungan tersebut. Jadi ketika RFID reader mendeteksi RFID tag pada gantungan kunci pemilik sepeda motor dan sesuai maka sistem engine pada sepeda motor akan on. Kantor Kecamatan Plantungan merupakan kantor Kecamatan yang terletak di desa Plantungan  Kabupaten Kendal Provinsi Jawa Tengah dengan kepala camat bernama bapak Suyanto. Letak Kantor Kecamatan Plantungan yang tidak terlalu dekat dengan warga sangat memungkinkan terjadinya aksi pencurian atau pembobolan di dalam Kantor Kecamatan Plantungan apalagi di kantor Kecamatan Plantungan saat malam hari, dalam hal ini sangat memudahkan pencuri untuk masuk kedalam kantor Kecamatan dengan mudah.

Broiler chickens are livestock whose growth is influenced by environmental temperature. The temperature of the chicken coop that is not suitable can affect the decrease in productivity and cause death in broiler chickens, so that the temperature setting of the cage must be considered. The design of this temperature and humidity monitoring system uses a nodemcu ESP8266 microcontroller and an arduino uno. If the measured temperature exceeds the set temperature limit, the system will send an SMS to the smartphone so that the cage officer can take appropriate action.

Honey is a natural liquid that contains a lot of sugar produced by bees (genus Apis) from flower nectar and has a sweet taste. Honey contains a multitude of benefits that are good for the body, including being a source of nutrients, improving body metabolism, anti-bacterial, and others. The purpose of designing the Honey Harvest Monitoring System with ARDUINO-based IOT is to help breeders maximize honey harvesting results. This study aims to design an intelligent system for controlling the temperature in bee hives, humidity in bee hives, and monitoring honey yields, measuring the temperature and humidity of the storage room using DHT 11 sensors, and monitoring honey harvest time using Load Cell sensors. The temperature and humidity controller in the cage uses a blower/fan. Sensor data will be processed using the Wemos D1 R1 microcontroller and then sent to an Android application via the internet network using a real-time Firebase database so that it can be accessed anywhere and anytime. The way this system works is that if the room temperature is >38 degrees Celsius, the blower/fan will turn on, and will turn off if the temperature is 40%, the artificial window will open and will close if the humidity is

One of the automatic sink products was made by Yogyakarta Technology University students. It is felt that this automatic sink product needs to be tested for its usability or ease of use. The USE questionnaire was used to carry out this test, and five test parameters were used. specifically, learning ability, efficiency, memory, error avoidance, and satisfaction. Based on its use, the purpose of this paper is to find out the user's opinion about the automatic sink product. The distribution of the USE questionnaire consisting of ten questions and five rating points on a Likert Scale was used to conduct this kind of quantitative descriptive research on consumers of automatic sink products. This study obtained usability measurement results for automatic sink products with a value of 84.67% on learnability, 96.22% on efficiency, 82.44% on memoriability, 88% on errors and 76.88% on satisfaction.

Internet-of-Things (IoT) merupakan teknologi yang mengintegrasikan berbagai peralatan dengan Internet. Salah satu pemanfaatan IoT adalah sistem kontrol elektronik pada berbagai peralatan rumah. Peralatan rumah dapat dilengkapi dengan mikrokontroler, sensor, dan aktuator, serta modul komunikasi, sehingga dapat dihubungkan ke internet dan dipantau dari jarak jauh. Salah satu peralatan atau objek yang ada di rumah adalah tempat sampah yang umumnya terbuat dari plastik, tetapi umumnya belum dapat dipantau dan dikontrol otomatis. Tujuan penelitian ini adalah untuk merancang sistem kontrol untuk membuka dan menutup tempat sampah secara otomatis menggunakan Arduino sebagai pengontrol sistem, sensor ultrasonik sebagai pendeteksi objek yang mendekat, motor servo yang berguna untuk menggerakkan tutup tempat sampah, dan buzzer serta LED sebagai indikator ketika terdapat objek yang mendekat. Hasil pengujian sistem menunjukkan bahwa tempat sampah dapat membuka tutupnya secara otomatis saat mendeteksi objek pada jarak paling jauh 50 cm dengan delay selama dua detik, dan kemudian akan tertutup secara otomatis ketika objek tersebut menjauh dari tempat sampah tersebut.

Advances in automation technology in industries that run very fast have spurred every educational institution to be able to keep up. Every SMK is no exception, which is tasked with preparing and producing students to be able to compete in the world of work. One of the automation technologies is PLC and SCADA which are widely used in the industrial world, for this reason, it is necessary for Muhammadiyah Gresik University students, especially the Electrical Engineering study program, to share knowledge about one of the PLCs and SCADA by using Outseal as PLC and Haiwell as SCADA at SMKN Singosari, Malang in the form of community service activities. By providing training on the basics of PLC and SCADA using Outseal software as a PLC which is uploaded to Arduino and Haiwell as an HMI for SMK students in understanding the basics of PLC which is then followed by simulating cases that often occur in the industry. The results of the student response were very positive giving an assessment of more than 90% and wanting a similar training with a different theme.

Seiring perkembangan zaman dan teknologi yang pesat saat ini, dalamkehidupan sehari-hari manusia tidak pernah lepas dari aktivitasnya untuk berinteraksi dengan peralatan elektronik yang membantu dan mempermudah pekerjaan manusia. Salah satunya adalah brankas otomatis dengan keamanan menggunakan sensor facerecognition dan fingerprint supaya perhiasan dan barang berharga lainnya lebih terjamin keamanannya dengan sistem keamanan ganda pada brankas.   Proyek akhir ini bertujuan untuk mengembangkan sebuah teknologi yang memanfaatkan beberapa macam komponen sensor, dimana komponen sensor tersebut melibatkan sensor getar untuk mengirimkan sms gateway jika brankas berpindah tempat, dan sim800l akan mengirimkan titik kordinat brankas berupa sms gateway. Dan GPS akan melacak keberadaan brankas sesuai titik kordinat tersebut. Buzzer akan berbunyi untuk memberikan tandaatau notifikasi.

The research method used in this study is the research and development method or also called Research and Development. The research design that will be developed in this study uses the development model presented by Borgan Gall. The product produced in this study is an Arduino Nano-Based Distance Measuring Tool with a Display on the LCD on the Flat Side Room Building Material for Class VIII at SMP Negeri 5 Sepauk. The test subjects of this study included two subjects. The first subject is the validator and the second is class VIII students of SMP Negeri 5 Sepauk. The analysis technique used is to determine the effectiveness, practicality, and validity. The percentage of effectiveness from the average of the two analyzes obtained a percentage value of 94.06% with Very Effective criteria used in learning mathematics. The results of the combined teacher and student response questionnaires - the average percentage obtained was 89.55% with very practical criteria. The combined results of the average percentage obtained from the percentage of experts and the results of the measurement trials obtained a percentage of 76,36% with very valid criteria.    

This research aims to ease the work of freshwater ornamental fish breeders who use aquariums or can also be implemented in ordinary ponds. Usually cultivators work using extra (manual) labor to be more effective using tools.                This research is a type of development research with reference to the R & D (Research And Development) method.                The results of the study show that, in testing the tool can function properly. All components and sensors can function with 85% accuracy. Thus, Aquarium Water Replacement Automation Using Turbidity and Arduino Uno is suitable for use by cultivators.

This research aims to ease the work of freshwater ornamental fish breeders who use aquariums or can also be implemented in ordinary ponds. Usually cultivators work using extra (manual) labor to be more effective using tools.                This research is a type of development research with reference to the R & D (Research And Development) method.                The results of the study show that, in testing the tool can function properly. All components and sensors can function with 85% accuracy. Thus, Aquarium Water Replacement Automation Using Turbidity and Arduino Uno is suitable for use by cultivators.