Publication Search

Menurut data dari BPJS, kecelakaan kerja yang terjadi di Indonesia pada bulan Januari hingga November 2022 sebanyak 265.334 kasus. Jumlah ini meningkat 13,26 persen dibandingkan 234.270 kasus pada tahun 2021. Data tersebut menjadi peringatan keras bahwa pelaksanaan keselamatan dan kesehatan kerja (K3) harus semakin menjadi perhatian. UD Cantenan menggunakan beberapa mesin, bahan-bahan kimia dan suhu yang tinggi, dan hampir seluruh proses dilakukan masih secara manual tanpa alat bantu dan dioperasikan langsung. Berdasarkan obeservasi yang dilakukan terdapat 34 risiko kecelakaan kerja yang terdapat pada bagian proses produksi dan tercatat ada 14 kasus kecelakaan kerja yang terdapat pada bagian produksi di Ud Cantenan, data tersebut diambil dari bulan Febrari tahun 2020 hingga bulan Juli tahun 2023. Metode JSA digunakan untuk menentukan pekerjaan yang dianalisis serta mengidentifikasi risiko pada masing-masing pekerjaan, Metode FMEA difungsikan untuk mengidentifikasi tingkat risiko kecelakaan kerja yang mengukur dari aspek dampak, peluang kejadian dan pencegahaannya dilakukan, sedangkan metode FTA digunakan untuk mengdentifikasi potensi penyebab kecelakaan. Dari hasil analisis data diketahui bahwa 5 failure mode dengan nilai RPN terbesar yaitu, terkena tumpahan logam cair,, tergulung putaran chuck mesin turning, tersengat listrik, tergulung putaran mata pahat milling dan mata terkena sekrap logam sisa produksi, ke lima failure mode dengan nilai RPN tertinggi yaitu fm 14, fm 27, fm 31 dengan nilai RPN 75 dan fm 22, fm 28 dengan nilai RPN 64. Nilai RPN tertinggi nantinya akan dilakukan analisis FTA untuk mengetahui akar penyebab masalah dan diberikan rekomendasi untuk perbaikan, untuk FM 14, 21, dan 38 memiliki tiga akar masalah, sedangkan fm 27 dan 28 memiliki 4 akar masalah.

This study aims to determine the number of rejected products (products that do not meet consumer and company standards) for 220 mL cup products using the six sigma method with 5 stages (define, measure, analyze, improve, and control) which will then be given improvement recommendations using failure mode effect analyze (FMEA). After going through the calculation process, it is known that the company's Deffect Per Million Opportunity (DPMO) value is 3.67 which indicates that the percentage of production without deffects is 96.32%. There are four critical to process (CTQ) in the 220 mL cup defect and the largest is the skewed seal with a percentage of 70%. The results of calculations using risk priority number (RPN) found recommendations in the form of corrective actions in 80% of the group of causes of oblique seal deffects so that it is hoped that the company will review and make improvements to the proposal so as to reduce deffects per million opportunity (DPMO) in the 220 mL cup production unit.                                                                                                      

Unsmooth milk production is the main problem causing the failure of the breastfeeding process. One way to increase milk production for post partum mothers is to support the nutritional needs of mothers, one of which is by consuming soy milk made from soy beans. This study aims to determine the effec tof soymilk (Glycine Max) on breast milk production in post partum mothers at Bakti Timah Hospital Karimun Riau Archipelgo. This researchis a pre-experimental study with a one-group pretest-posttest design. The population in this study were post partum mothers at Bakti Timah Hospital Karimun Riau Archipelago in the last one month as many as 102 people. The sampling technique in this study used a sampling technique carried out using purposive sampling of 34 respondents. The research instrument used a breastmilk production questionnaire, namely the Lactation Assessment Tool (LATCH) which consisted of 5 points. Data analysis was performed univariately and bivariately using the Wilcoxon test. The results showed that before consuming soy milk the average milk production was 3.35 and after being given soy milk the average milk production increased to 4.03. The results of the Wilcoxon test found a p-value of 0.001 (p <0.05) so it can be concluded that there is an effect of soy milk (Glycine Max) on increasing milk production in post partum mothers. It is recommended for the community, especially post partum mothers, to be able to use soy milk as an alternative to addressing problems with increasing breast milk production.

Indonesia has a significant problem of economic inequality between regions. This can give rise to inequality and social injustice. The government, in its efforts to achieve economic equality between regions in its national development strategy, has provided several policies, however, it also needs a national development strategy with an Islamic perspective to perfect these policies. This study employed a qualitative approach as its research methodology, specifically focusing on library research. A qualitative approach allows researchers to understand complex and multidimensional phenomena. In facing the challenges, challenges and failures in the national development strategy in Indonesia in the last 10 years, Islamic Economics can provide alternative solutions that can strengthen the parts that according to Islamic Economics must also be considered in order to strengthen the National Development strategy that can minimize and neutralize, one of which is by paying attention to Sharia Economic Principles in terms of development such as justice, balance and poverty. Therefore, the national development strategy implemented must pay attention to these principles. From the standpoint of Islamic economic development, Indonesia's development focus for the past ten years has been irrelevant. This is a result of the Indonesian government continuing to focused on infrastructure development and is not fully in accordance with sharia principles, and is lacking in improving the aspect of human resources.

Through web-based business applications, it helps start-up companies to reach their target markets more quickly and in a more organized manner, with a more efficient level of economic costs compared to using conventional consumer marketing methods which require higher levels of economic costs. However, more than 40% of SMEs and startup companies in Indonesia, both digital and non-digital based, experience financial failure and fail to maintain their business continuously, due to inefficient management of the financial aspects of the organization, which becomes an obstacle for business actors in planning and can also disrupt the level of continuity of the business. This is the background for the need for community service activities in order to improve the quality of financial inclusion, especially in terms of working capital management budgeting for mobile-based SMEs and startup companies.  This community service activity was formed to expand knowledge regarding effective and efficient working capital management budgeting, where it is hoped that through this program, mobile-based SMEs and startup business actors will have the knowledge to know the financial strength of their business and can be used as a consideration in decisions and make the business run healthier in the future.

As innovation develops and the human population increases, product competition between companies increases, so producers are required to produce goods as quickly as possible while still considering the quality aspects of the product. PT. Cipta Oggi is a company engaged in furniture production. PT. Cipta Oggi has several types of production, namely office tables, cupboards, TV shelves and decorative cupboards. In the production process for the 2DF WHT polo showcase furniture product, it has the highest rework rate, namely 10.67%. The method used in this research is the FMEA method. The FMEA method will later produce output results in the form of an RPN from which recommendations for improvement will be obtained from the types of causes of failure that are the highest. With this research, the aim is to analyze the causes of rework in the production process of Polo Showcase 2DF WHT furniture products which can later reduce the rework rate.

Abstract. UD Cantenan is an industrial company engaged in metal casting, especially made from Aluminum. This company is known to have quality control problems in the manufacture of lip handle products and canal parts. The result of this problem is defective products in the lip handle and canal parts. In this case, of course, the company will spend more to repair the product so that the company experiences losses. Companies need to find ways to reduce the number of defective products. In this study, the Six Sigma method was used with DMAIC (Define, Measure, Analyze, Improve Control) and TRIZ stages to analyze and provide solutions to improve problems that occurred in the company. Based on the research conducted, at the define stage there are 3 types of defects in the lip handle product and canal parts, namely small scratches, small pinholes, and asymmetrical patterns. Then the measure stage obtained the percentage of small scratch defects of 54.47%, small pinholes of 17.3% and asymmetrical patterns of 28.2%. The average DPMO score obtained is 25,720 with a sigma level of 3.45 which shows that UD Cantenan can be categorized as good for industry in Indonesia. Furthermore, at the analysis stage Based on the identification of causal factors using FMEA analysis, it is known that the biggest contributing factor to failure is operator error in the operation of the milling machine. Then at the improve stage, make improvement proposals based on obtaining the highest RPN value from the factors causing disability using the TRIZ method. And the last stage, namely control, is the result of proposed improvements that can be made by the company to solve problems to reduce the number of product defects that occur during the production process.