Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC

Maulana ; Idris ; Lukman David ; Hendis Rizqias Domoros ; Budi Harjo
Mars: Jurnal Teknik Mesin, Industri, Elektro Dan I... 📅 2025 Vol 3, No 6 🔗 DOI: 10.61132/mars.v3i6.1196
Abstract
This study aims to analyze product quality at PT. XYZ, particularly focusing on Defects by Dimension, using the Statistical Quality Control (SQC) method. Defect data were collected over the period from April 2024 to March 2025 and analyzed using seven SQC tools, namely the check sheet, histogram, Pareto Chart, Scatter Diagram, and p-Chart. The results indicate that Defects do not always increase in proportion to production volume, and the most dominant types of Defects are Dimensional and Hole Distance, accounting for 73.4% of the total Defects based on the Pareto Chart. The Scatter Diagram shows an upward trend in Defects as production increases up to a certain point, after which the Defect rate decreases as production continues to rise. The p-Chart indicates that the production process remains within statistical control limits, although several samples approach or slightly exceed the upper control limit. Overall, the quality control process is fairly well maintained; however, greater attention is needed to address dominant Defect types and variations near control limits to prevent larger process deviations.
Keywords
Defect Dimension; Pareto Chart; Quality Control; Scatter Diagram; SQC
How to Cite

Maulana, et al. (2025). Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC. Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer, 3(6). https://doi.org/10.61132/mars.v3i6.1196

Maulana, Idris; Lukman David; Hendis Rizqias Domoros; Budi Harjo, "Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC," Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer, vol. 3, no. 6, 2025.

Maulana, Idris; Lukman David; Hendis Rizqias Domoros; Budi Harjo. "Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC." Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer, vol. 3, no. 6, 2025.

Maulana, Idris; Lukman David; Hendis Rizqias Domoros; Budi Harjo. "Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC." Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer 3, no. 6 (2025).

Maulana, et al. (2025) 'Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC', Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer, 3(6). doi: 10.61132/mars.v3i6.1196.

Maulana, Idris; Lukman David; Hendis Rizqias Domoros; Budi Harjo. Analisa Pengendalian Defect Product by Dimension di PT, XYZ Menggunakan Metode SQC. Mars: Jurnal Teknik Mesin, Industri, Elektro Dan Ilmu Komputer. 2025;3(6).

Artikel Terkait

Perancangan Produk Sabun Cuci Piring Cair Berbahan Dasar Buah Lerak

Carla Lovely Laurisa; Shafa Dhiya Ulhaq; Rifky Rifai; Nurjannah Nurjannah

Produksi Daun Gergaji Baja 2 Sisi Tajam, Ukuran 310x30x0,8 mm, Kapasitas 20 Biji/Jam

Rismatul Hasanah; Syamsul Hadi; Gilang Febriyan Mahendra; Muhammad Ilham Sujatmiko; Ahmad Jibril Muqorrobin; Mukhamad Rony Efendi

Pengaruh Ketebalan Core dan Jumlah Layer Skin terhadap Kekuatan Bending Komposit Sandwich Skin Fiberglass dengan Core Kardus Tipe A-Flute

Pires Hanif Palarto; Hilmi Iman Firmansyah

Fabrikasi Peniti Bros Panjang 60 mm, Diameter 0,5 mm, Bahan AISI 1045, Kapasitas 40 Unit/Jam

Adib Fahrur Rozi; Syamsul Hadi; Dava Ilham Ibrahimovic; Muhammad Nashih Taufiqie; Bintang Bimantara Putra Pribadi; Mahesa Haryo Torayoga

Manufaktur Kunci Pas-Kunci Ring M14mm Baja Tempa, Ukuran 200x6,5mm, Kapasitas 20 Biji/Jam

Balena Insan Faza; Syamsul Hadi; Reynaldi Wahyu Ramadhan; Azril Ihza Fahreza; Emir Rashid Hibatullah; Shoultan Rashid Alahuddin

Pengaruh Variasi Beban dan Kecepatan terhadap Arus Motor Hub BLDC pada Sepeda Listrik

Fariz Hernanto Oktafiandri; Eko Yudiyanto
Tren Sitasi Jurnal